Suzuki GSX-R 1000 Service Manual: Crankshaft journal bearing inspection and selection
Refer to “engine bottom side disassembly” (page 1d- 49).
Refer to “engine bottom side assembly” .
Inspection
- Inspect each upper and lower crankcase bearing for any damage.
- Set the crankshaft onto the upper crank case.
- Install the plastigauge onto each crankshaft journal.
Special tool
(a): 09900–22301 (plastigage (0.025 –
0.076
Mm))
- Mate the lower crankcase with the upper crankcase.
- Tighten the crankshaft journal bolts (m9). Tighten each bolt a little at a time to equalize the pressure in the following two steps.
| Note do not rotate the crankshaft when a piece of plastigauge is installed. |
Tightening torque crankshaft journal bolt (m9): 18 n·m (1.8 Kgf-m, 13.0 Lbf-ft) then turn in 50°
- Remove the lower crankcase and measure the width of compressed plastigauge using the envelope scale. This measurement should be taken at the widest part of the compressed plastigauge. If the oil clearance exceeds the service limit, select the specified bearings from the bearing selection table.
Crankshaft journal oil clearance standard: 0.016 – 0.034 Mm (0.0006 – 0.0013 In)
Crankshaft journal oil clearance service limit: 0.080 Mm (0.0031 In)
Selection
- Check the corresponding crankcase journal i.D.
Codes “a” ([a], [b] or [c]), which are stamped on the rear of the upper crankcase.
Crankcase journal i.D. Specification
- Check the corresponding crankshaft journal o.D.
Codes “b” ([a], [b] or [c]), which are stamped on the crankshaft.
- Measure the crankshaft o.D. With the special tool. If any of the measurements are out of specification, replace the crankshaft.
Crankshaft journal o.D. Specification
Special tool
(a): 09900–20202 (micrometer (25 –
50
mm))
- Select the specified bearings from the bearing selection table
Bearing selection table
Bearing thickness specification
|
Conrod crank pin bearing inspection and
selection
Refer to “engine bottom side disassembly” (page 1d-
49).
Refer to “engine bottom side assembly” .
Inspection
Inspect the bearing surfaces for any signs of fusion,
pitting, burn or flaws. If ...
Crankshaft thrust clearance inspection and
selection
Refer to “engine bottom side disassembly” (page 1d-
49).
Refer to “engine bottom side assembly” .
Inspection
With the crankshaft’s right-side and left-side thrust
bearings inserted into the ...
Other materials:
Rear brake disc inspection
Brake disc thickness
Check the brake disc for damage or cracks and measure
the thickness using the micrometer.
Replace the brake disc if the thickness is less than the
service limit or if defect is found.
Special tool
(a): 09900–20205 (micrometer (0 –
25 mm))
Brake disc thickness
service ...
Gearshift shaft construction
Gearshift shaft
Washer
Snap ring
Gearshift shaft return spring
Gearshift cam drive plate
Gearshift plate return spring
8.5 N·m (0.85 Kgf-m,
6.0 Lbf-ft)
13 N·m
(1.3 Kgf-m, 9.5 Lbf-ft)
19 N·m
(1.9 Kgf-m, 13.5 Lbf-ft)
Apply ...
Tp reset
When replacing the throttle body assembly or tp sensor
with a new one or reinstalling the tp sensor, reset the
tp learned value in the following procedures:
Note
keep the throttle valves fully closed while
resetting the tp learned value.
Turn the ignition switch on.
...