Detected condition and possible cause
Detected condition |
Possible cause |
||
C14 | Output voltage is not within the following
range. Difference between actual throttle opening and opening calculated by ecm is larger than specified value. 0.2 V ≤ Sensor voltage < 4.8 V |
|
|
P0120 | H | Sensor voltage is higher than specified value. |
|
L | Sensor voltage is lower than specified value. |
Wiring diagram
Troubleshooting
Caution when using the multi-circuit tester, do not strongly touch the terminal of the ecm coupler with a needle pointed tester probe to prevent terminal damage. |
Note after repairing the trouble, clear the dtc using sds tool. Refer to “use of sds diagnosis reset procedures” . |
C14 (use of mode select switch)
Step |
Action |
Yes |
No |
1 |
Special tool
(a): 09900–25008 (multi
Tester knob indication voltage ( ) Tp sensor input voltage 4.5 – 5.5 V ((+) terminal: r – (–) terminal: ground, (+) terminal: r – (–) terminal: b/br) Is the voltage ok? |
Go to step 3. |
|
P0120-h (use of sds)
Step |
Action |
Yes |
No |
1 |
Special tool Tester knob indication continuity ( )
Special tool Tester knob indication continuity test ( ) Ecm couplers (harness side) Is the continuity ok? |
Go to step 3. | P/b wire shorted to vcc, or b/br wire open |
P0120-l (use of sds)
Step |
Action |
Yes |
No |
1 |
Special tool Tester knob indication continuity test ( )
Special tool Tester knob indication continuity test ( ) Ecm couplers (harness side) Is the continuity ok? |
Go to step 2. | R or p/b wire open, or y/w wire shorted to ground. |
2 |
Special tool Tester knob indication voltage ( ) Tp sensor input voltage 4.5 – 5.5 V ((+) terminal: r – (–) terminal: ground, (+) terminal: r – (–) terminal: b/br) Is the voltage ok? |
Go to step 3. | Open or short circuit in the r or b/br wire. |
3 |
Special tool Tester knob indication voltage ( ) Tp sensor output voltage throttle valve is closed: approx. 1.1 V throttle valve is opened: approx. 4.4 V ((+) terminal: p/b – (–) terminal: b/br) Is the voltage ok? |
|
If check result is not
satisfactory, replace tp
sensor with a new one. Refer to “throttle body disassembly and assembly” in section 1d . |
Drive chain cleaning and lubricating
Clean and lubricate drive chain
every 1 000 km (600 miles)
Clean and lubricate the drive chain in the following
procedures:
clean the drive chain with kerosine. If the drive chain
tends to rust quickly, the intervals must be
shortened.
Caution
do not use trichloroethyle ...
Body frame construction
Frame
Seat rail
Seat rail bolt
Collar
Engine mounting thrust adjuster
Engine mounting thrust adjuster lock-nut
Engine mounting pinch bolt
50 N·m (5.0 Kgf-m,
36.0 Lbf-ft)
23 N·m
(2.3 Kgf-m, 16.5 Lbf-ft)
45 N·m
(4.5 Kgf-m, 32. ...
Damping force adjustment
The rebound and compression
damping force can be individually
adjusted by turning the respective
adjusters. The rebound damping
force adjuster 2 is located at the
top of the front fork. The compression
damping force adjuster 3 is
located at the bottom of the front
fork.
To adjust the da ...