Suzuki GSX-R 1000 Service Manual: Dtc “c32” (p0201), “c33” (p0202), “c34” (p0203) or “c35” (p0204): primary fuel injector circuit malfunction

Suzuki GSX-R 1000 Service Manual / Engine / Engine general information and diagnosis / Diagnostic information and procedures / Dtc “c32” (p0201), “c33” (p0202), “c34” (p0203) or “c35” (p0204): primary fuel injector circuit malfunction

Detected condition and possible cause

Detected condition

Possible cause

Ckp signal is produced but fuel injector signal is interrupted by 4 times or more continuity

Injector circuit open or short.
Injector malfunction.
Ecm malfunction.

Wiring diagram

Suzuki GSX-R. Wiring diagram

Troubleshooting

Caution

when using the multi-circuit tester, do not strongly touch the terminal of the ecm coupler with a needle pointed tester probe to prevent terminal damage.

Note

after repairing the trouble, clear the dtc using sds tool. Refer to “use of sds diagnosis reset procedures” .

Step

Action

Yes

Turn the ignition switch off.
Lift and support the fuel tank. Refer to “fuel tank removal and installation” in section 1g .
Check the primary fuel injector coupler (1) for loose or poor contacts.

If ok, then measure the injector resistance.

Disconnect the injector coupler and measure the resistance between terminals.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Tester knob indication resistance (Ω)

Injector resistance 11 – 13 Ω at 20 °c (68 °f) (terminal – terminal)

If ok, then check the continuity between each terminal and ground.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Injector continuity ∞Ω¶ (infinity)

Are the resistance and continuity ok?

Go to step 2.

Replace the injector with a new one. Refer to “throttle body disassembly and assembly” in section 1d .

Turn the ignition switch on.
Measure the injector voltage between the y/r wire and ground.

Note

injector voltage can be detected only for 3 seconds after ignition switch is turned on.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Tester knob indication voltage ( )

Injector voltage battery voltage ((+) terminal: y/r – (–) terminal: ground)

Is the voltage ok?

Gr/w wire open or shorted to ground, or poor “46” connection (#1 cylinder side).
Gr/b wire open or shorted to ground, or poor “45” connection (#2 cylinder side).
Gr/y wire open or shorted to ground, or poor “44” connection (#3 cylinder side).
Gr/r wire open or shorted to ground, or poor “43” connection (#4 cylinder side).
If wire and connection are ok, intermittent trouble or faulty ecm.
Recheck each terminal and wire harness for open circuit and poor connection.
Replace the ecm with a known good one, and inspect it again. Refer to “ecm removal and installation” in section 1c .

Open circuit in the y/r wire.

DTC “c31” (p0705): gp switch circuit malfunction

Detected condition and possible cause Detected condition Possible cause No gear position switch voltage Gp switch voltage is not within the following range. Gp switch ...

Dtc “c36” (p1764), “c37” (p1765), “c38” (p1766) or “c39” (p1767): secondary fuel injector circuit malfunction

Detected condition and possible cause Detected condition Possible cause Some failure exists in the fuel injector signal in a high load, high revolution condition. ...

Other materials:

Accessory use
The addition of unsuitable accessories can lead to unsafe operating conditions. It is not possible for suzuki to test each accessory on the market or combinations of all the available accessories; however, your dealer can assist you in selecting quality accessories and installing them correc ...

Crankshaft thrust clearance inspection and selection
Refer to “engine bottom side disassembly” (page 1d- 49). Refer to “engine bottom side assembly” . Inspection With the crankshaft’s right-side and left-side thrust bearings inserted into the upper crankcase. Measure the thrust clearance “a” between the leftside thrust bearing and ...

Water pump construction
Impeller Mechanical seal Oil seal O-ring O-ring 8 N·m (0.8 Kgf-m, 6.0 Lbf-ft) 10 N·m (1.0 Kgf-m, 7.0 Lbf-ft) Apply grease. Apply engine coolant. Apply molybdenum oil solution. Do not reuse. ...