Toyota RAV4 manuals

Suzuki GSX-R 1000 Service Manual: Dtc “c36” (p1764), “c37” (p1765), “c38” (p1766) or “c39” (p1767): secondary fuel injector circuit malfunction

Suzuki GSX-R 1000 Service Manual / Engine / Engine general information and diagnosis / Diagnostic information and procedures / Dtc “c36” (p1764), “c37” (p1765), “c38” (p1766) or “c39” (p1767): secondary fuel injector circuit malfunction

Detected condition and possible cause

Detected condition

Possible cause

Some failure exists in the fuel injector signal in a high load, high revolution condition.
  • Injector circuit open or short.
  •  Injector malfunction.
  •  Ecm malfunction.

Wiring diagram

Suzuki GSX-R. Wiring diagram


Troubleshooting

Caution

when using the multi-circuit tester, do not strongly touch the terminal of the ecm coupler with a needle pointed tester probe to prevent terminal damage.

 

Note

after repairing the trouble, clear the dtc using sds tool. Refer to “use of sds diagnosis reset procedures” .

 

Step

Action

Yes

No

1

  1. Turn the ignition switch off.
  2.  Lift and support the fuel tank. Refer to “fuel tank removal and installation” in section 1g .
  3.  Check the secondary fuel injector coupler (1) for loose or poor contacts.

    If ok, then measure the injector resistance.


  1. Disconnect the injector coupler and measure the resistance between terminals.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Tester knob indication resistance (Ω)

Injector resistance 11 – 13 Ω at 20 °c (68 °f) (terminal – terminal)


  1. If ok, then check the continuity between each terminal and ground.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Injector continuity ∞Ω¶ (infinity)


Are the resistance and continuity ok?

Go to step 2. Replace the injector with a new one. Refer to “throttle body disassembly and assembly” in section 1d .

2

  1. Turn the ignition switch on.
  2.  Measure the injector voltage between the y/r wire and ground.
Note

injector voltage can be detected only for 3 seconds after ignition switch is turned on.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Tester knob indication voltage ( )


Injector voltage battery voltage ((+) terminal: y/r – (–) terminal: ground)


Is the voltage ok?

  • Lg wire open or shorted to ground, or poor “59” connection (#1 cylinder side).
  •  Lg/w wire open or shorted to ground, or poor “58” connection (#2 cylinder side).
  •  Lg/b wire open or shorted to ground, or poor “57” connection (#3 cylinder side).
  •  Lg/bl wire open or shorted to ground, or poor “56” connection (#4 cylinder side).
  •  If wire and connection are ok, intermittent trouble or faulty ecm.
  •  Recheck each terminal and wire harness for open circuit and poor connection.
  •  Replace the ecm with a known good one, and inspect it again. Refer to “ecm removal and installation” in section 1c .
Open circuit in the y/r wire.
Dtc “c32” (p0201), “c33” (p0202), “c34” (p0203) or “c35” (p0204): primary fuel injector circuit malfunction
Detected condition and possible cause Detected condition Possible cause Ckp signal is produced but fuel injector signal is interrupted by 4 times or more continuity ...

DTC “c40” (p0505 / p0506 / p0507): isc valve circuit malfunction
Detected condition and possible cause Detected condition Possible cause C40/P0505 The circuit voltage of motor drive is unusual. Isc valve circuit open or ...

Other materials:

Radiator cap inspection
Inspect the radiator cap in the following procedures:  remove the radiator cap. Refer to “cooling circuit inspection” .  Attach the radiator cap (1) to the radiator tester (2) as shown. Slowly apply pressure to the radiator cap. If the radiator cap does not hold the pre ...

Exhaust pipe bolt and muffler bolt inspection
Tighten exhaust pipe bolts and muffler bolts initially at 1 000 km (600 miles, 2 months) and every 12 000 km (7 500 miles, 24 months) thereafter Check the exhaust pipe bolts and muffler bolts to the specified torque. Tightening torque exhaust pipe bolt (a): 23 n·m (2.3 Kgf-m, 16.5 Lbf-ft) muf ...

Schematic and routing diagram
Fuel tank drain hose and breather hose routing diagram Fuel tank water drain hose Fuel tank breather hose no. 1 Fuel tank breather hose no. 2 Fuel tank breather hose no. 3 3-Way joint Frame White marking Set the hose end to the root of tank nippl ...

© 2011-2024 Copyright www.suzukigsxr.org