Suzuki GSX-R 1000 Service Manual: DTC “c93” (p1769): steering damper solenoid valve circuit malfunction

Suzuki GSX-R 1000 Service Manual / Engine / Engine general information and diagnosis / Diagnostic information and procedures / DTC “c93” (p1769): steering damper solenoid valve circuit malfunction

Detected condition and possible cause

Detected condition			Possible cause
C93		Steering damper control current does not flow to the solenoid valve. With ig turned on, ecm detects a failure of internal circuit element. Solenoid current does not converge to the target value. Battery voltage is 10 v or below with the engine running.	Steering damper solenoid valve circuit interrupter element shorted. Feedback current convergence failure. Low battery voltage. Ecm malfunction. Steering damper solenoid valve circuit shorted to vcc. Steering damper solenoid valve circuit open. Steering damper solenoid valve circuit shorted.
P1769	H	Steering damper control current is higher than specified value. An abnormal current is detected during the vehicle standstill. Solenoid current is 0.7 A or above.
	L	Steering damper control current is lower than specified value. With ig turned on, ecm detects a discontinuity. An abnormal current is detected during the vehicle standstill.

Wiring diagram

Suzuki GSX-R. Wiring diagram

Troubleshooting

Caution

when using the multi-circuit tester, do not strongly touch the terminal of the ecm coupler with a needle pointed tester probe to prevent terminal damage.

Note

after repairing the trouble, clear the dtc using sds tool. Refer to “use of sds diagnosis reset procedures” .

Step

Action

Yes

Turn the ignition switch off.
Check the steering damper solenoid valve coupler (1) for loose or poor contacts.

If ok, then measure the steering damper solenoid valve resistance.

Disconnect the steering damper solenoid valve coupler.
Measure the steering damper solenoid valve resistance.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Tester knob indication resistance (Ω)

Steering damper solenoid valve resistance approx. 12.5 Ω at 20 °c (68 °f)

Is the resistance ok?

Go to step 2.

Replace the steering damper with a new one.

Turn the ignition switch on.
Measure the voltage between b/bl wire and ground.

Special tool
(a): 09900–25008 (multi
circuit tester set)

Tester knob indication voltage ( )

Steering damper solenoid valve voltage approx. 10 V when battery is fully charged condition ((+) terminal: b/bl – (–) terminal: ground)

Is the voltage ok?

B/bl (w) wire shorted to vcc, or poor “26” connection failure.
B/o (br) wire open or shorted to ground, or poor “25” connection failure.
If wire and connection are ok, intermittent trouble or faulty ecm.
Recheck each terminal and wire harness for open circuit and poor connection.
Replace the ecm with a known good one, and inspect it again.

Low battery voltage or fuse is blown.
B/bl (w) wire open or shorted to ground, or poor “26” connection failure.
If wire and connection are ok, intermittent trouble or faulty ecm.
Recheck each terminal and wire harness for open circuit and poor connection.
Replace the ecm with a known good one, and inspect it again.

Active control inspection

Set up the sds tool. (Refer to sds operation manual for further details.)
Raise the front wheel off the ground.
Turn the ignition switch on.
Click “steering damper solenoid operating control” (1).

Suzuki GSX-R. Active control inspection

Click each button (2) on/off while turning the handlebars left and right.

Suzuki GSX-R. Active control inspection

Note

at this time, if the steering damping resistance changes from light to heavy by switching on/off, the function is normal.

DTC “c91” (p0500): vehicle speed sensor circuit malfunction

Detected condition and possible cause Detected condition Possible cause Speedometer does not receive signal from the vehicle speed sensor for more than 6 sec. When the m ...

Specifications

Service data Injector + fuel pump + fuel pressure regulator Fi sensors ...

Other materials:

Exhaust emission control system description
The exhaust emission control system is composed of the pair system, exhaust control system, ho2 sensor, threeway catalyst system and isc system. The fresh air is drawn into the exhaust ports through the pair control solenoid valve and pair reed valves. The pair control solenoid valve is operat ...

Conrod crank pin bearing inspection and selection
Refer to “engine bottom side disassembly” (page 1d- 49). Refer to “engine bottom side assembly” . Inspection Inspect the bearing surfaces for any signs of fusion, pitting, burn or flaws. If any, replace them with a specified set of bearings. Place the plastigauge axially along ...

Precautions
Precautions for clutch system Refer to “general precautions” in section 00 (page 00-1). Schematic and routing diagram Clutch cable routing diagram Refer to “throttle cable routing diagram” in section 1d . Diagnostic information and procedures Clutch system symptom diagnosis ...