Suzuki GSX-R 1000 Service Manual: Front fork removal and installation
| Note the right and left front forks are installed symmetrically and therefore the removal procedure for one side is the same as that for the other side. |
Removal
- Remove the front wheel. Refer to “front wheel assembly removal and installation” in section 2d .
Caution
|
- Disconnect the brake hoses from the clamps on the front fender.
- Remove the reflex reflectors (1). (Except for e-02, 19, 51)
- remove the front fender (2) by removing the bolts
- Loosen the front fork upper clamp bolt (3).
- Loosen the handlebar clamp bolt (4).
| Note slightly loosen the front fork cap (5) to facilitate later disassembly. |
Special tool
: 09941–53670 (front fork cap
socket
wrench (45 mm))
- Loosen the front fork lower clamp bolts (6) and remove the front fork.
| Note hold the front fork by hand to prevent it sliding out of the steering stem. |
Installation
- Set the front fork to the steering stem lower bracket temporarily by tightening the lower clamp bolts (1).
- Tighten the front fork cap (2) to the specified torque.
Tightening torque front fork cap (a): 35 n·m (3.5 Kgf-m, 25.5 Lbf-ft)
- Loosen the lower clamp bolts.
- Set the front fork with the edge of the outer tube positioned 7.0 Mm (0.28 In) “a” from the upper surface of the upper bracket.
|
- Tighten the front fork lower clamp bolts (1).
Tightening torque front fork lower clamp bolt (b): 23 n·m (2.3 Kgfm, 16.5 Lbf-ft)
- Tighten the front fork upper clamp bolt (3).
Tightening torque front fork upper clamp bolt (c): 23 n·m (2.3 Kgfm, 16.5 Lbf-ft)
- Tighten the handlebar clamp bolt (4).
Tightening torque handlebar clamp bolt (d): 23 n·m (2.3 Kgf-m, 16.5 Lbf-ft)
- Install the front wheel. Refer to “front wheel assembly removal and installation” in section 2d .
 After
remounting the brake calipers, pump the brake lever until the pistons push the pads correctly. |
| Note before tightening the front axle bolt and front axle pinch bolts, move the front fork up and down four or five times. |
Front fork components
Front fork cap
O-ring
Rebound damping force adjuster rod
Compression damping force adjuster rod
Piston rod nut
O-ring
Piston ring
Rod guide case
Spr ...
Front suspension adjustment
After installing the front fork, adjust the spring pre-load
and two kinds of damping force as follows:
Adjust the
left and right front forks to the
same setting.
Spring pre-load ...
Other materials:
The sport of motorcycling
Your motorcycle and this owner's
manual have been designed by
people like you who enjoy motorcycling.
People become motorcyclists
for many reasons. For
starters, street riding is fun and
invigorating. But no matter why
you became a motorcyclist, or
how experienced you are, you will
eventu ...
Special situations require special care
Of course, there are some times
when full-force braking is not the
correct technique. When the road
surface is wet, loose, or rough,
you should brake with care. When
you're leaned over in a corner,
avoid braking. Straighten up
before braking. Better yet, slow
down before entering the corner. ...
Pair system hose routing diagram
Pair control solenoid valve
Pair reed valve
White marking (hidden side)
Yellow marking
Blue marking
Red marking
Face the
clamp end to the top.
Make sure
the clamp is not contacted to the frame or air cleaner box.
90°
45°
15°
...