Suzuki GSX-R 1000 Service Manual: Transmission related parts inspection
Refer to “transmission removal” , “transmission installation” and “countershaft gear / driveshaft gear disassembly and assembly” .
Gearshift fork to groove clearance
| Note the clearance for each gearshift fork plays an important role in the smoothness and positiveness of the shifting action. |
Using the thickness gauge, check the gearshift fork clearance in the groove of its gear.
If the clearance checked is noted to exceed the limit specified, replace the fork or its gear, or both.
Special tool
(a): 09900–20803 (thickness gauge)
Gearshift fork to gearshift fork groove clearance standard: 0.1 – 0.3 Mm (0.004 – 0.012 In) service limit: 0.5 Mm (0.02 In)
Gearshift fork groove width
Measure the gearshift fork groove width using the vernier calipers.
Special tool
(a): 09900–20102 (vernier calipers
(200 mm))
Gearshift fork groove width standard: 5.0 – 5.1 Mm (0.197 – 0.201 In)
Gearshift fork thickness
Measure the gearshift fork thickness using the vernier calipers.
Special tool
(a): 09900–20102 (vernier calipers
(200 mm))
Gearshift fork thickness standard: 4.8 – 4.9 Mm (0.189 – 0.193 In)
Gearshift cam
Inspect the gearshift cam groove for abnormal wear and damage. If any defects are found, replace the gearshift cam with a new one.
Gearshift cam bearing
Inspect the gearshift cam bearings, left and right for abnormal noise and smooth rotation.
Replace the bearing if there is anything unusual. Refer to “transmission removal” and “transmission installation” .
Driveshaft bearing
Inspect the driveshaft left bearing for abnormal noise and smooth rotation while it is in the case.
Replace the bearing if there is anything unusual. Refer to “transmission removal” and “transmission installation” .
Inspect the driveshaft right bearing for abnormal noise and smooth rotation.
If there is anything unusual, replace the bearing assembly. Refer to “transmission removal” and “transmission installation” .
Driveshaft oil seal
Inspect the driveshaft left bearing dust seal for wear and damage.
Replace the dust seal if there is anything unusual. Refer to “transmission removal” and “transmission installation” .
Gear position (gp) switch inspection
Refer to “side-stand / ignition interlock system parts inspection” in section 1i .
Countershaft gear / driveshaft gear
disassembly and assembly
Refer to “transmission removal” and “transmission installation” .
Disassembly
Caution
identify the position of each removed part.
Organize the parts in their respective groups
...
Gear position (gp) switch removal and installation
Removal
Turn the ignition switch off.
Lift and support the fuel tank. Refer to “fuel tank
removal and installation” in section 1g (page 1g-
9).
Disconnect the gear position swi ...
Other materials:
Self-diagnosis function
The self-diagnosis function is incorporated in the ecm. The function has two
modes, “user mode” and “dealer mode”.
The user can only be notified by the lcd (display) panel and led (fi indicator
light). To check the function of the
individual fi system devices, the dealer mode is provided. In ...
Tampering with noise control system prohibited
Federal law prohibits the following
acts or the causing there of;
The removal or rendering inoperative
by any person other
than for purposes of maintenance,
repair, or replacement,
of any device or element of
·design incorporated into any
new vehicle for the purpose of
noise ...
Rear brake caliper parts inspection
Refer to “rear brake caliper disassembly and assembly” .
Brake caliper cylinder
Inspect the brake caliper cylinder wall for nicks,
scratches or other damage. If any damage is found,
replace the caliper with a new one.
Brake caliper piston
Inspect the brake caliper piston surface for any
s ...